AmpFlow P40-250-P brušeni električni motor, 250 W, 12 V, 24 V ili 36 VDC, 3400 RPM

Brand:AmpFlow

2.8/5

111.32

AmpFlow P40-250-P je palačinkasti motor s velikim okretnim momentom dizajniran za pružanje dobrih performansi i učinkovitosti po ekonomičnoj cijeni. To se postiže upotrebom četiri četke i naprednim elektromagnetskim računalnim modeliranjem i dizajnom. Motor je promjera 4,0 inča i dugačak 3,2 inča. Osovina se kreće u dva visokokvalitetna kuglična ležaja. Vodovi motora velikog promjera dugi su 14 inča. Motor je težak 4,2 funte i presvučen je visokokvalitetnim crnim premazom u prahu. Ovaj reverzibilni motor može se koristiti pri naponima u rasponu od 12 V do 36 Vdc. Na 24 volta, brzina praznog hoda je 3400 okretaja u minuti. Nazivna izlazna snaga je 250 W pri 2800 okretaja u minuti pri 14 A. Maksimalna učinkovitost je 78%. Ovaj motor dolazi s remenicom s 13 zuba za 5 mm HTD remen. Motori AmpFlow® koriste se u različitim primjenama, uključujući robote, električne skutere, električne bicikle i druge sustave osobnog prijevoza. Potražite AmpFlow motore na Amazonu za više izbora.

Kratki palačinka motor s remenicom s 13 zuba za 5 mm HTD remen. Vršna učinkovitost pri 24V: 78%. Kontinuirana snaga: 250 watta (1/3 konjske snage). Broj okretaja u minuti bez opterećenja: 3400 pri 24 volta; Može se koristiti s naponima u rasponu od 12V do 36VDC. Mjeri promjer od 4,0 inča (102 mm) i duljinu od 3,2 inča (81 mm).
Country of Origin USA
Item model number P40-250-P
Manufacturer Powerhouse Engineering Inc.
Package Dimensions 5.6 x 5.4 x 5.3 inches; 4.2 Pounds

2.8

8 Review
5 Star
32
4 Star
42
3 Star
9
2 Star
0
1 Star
17

Napišite svoju recenziju

Vaš email neće biti objavljen. Sva obavezna polja označena su s*

Scritto da: john angelosanto
is a ok motor
for generate dc power
Scritto da: A. W.
Probably ok if you need the pulley that comes with it.
I bought this motor with the intention of removing the pulley, as the seller stated was possible in one of the answered questions. Since the motor has a D shaft and a circlip, I assumed the pulley wouldn't be pressed on (or if it was, it wouldn't truly be an interference fit). I was wrong. On top of that, the pulley seems to be made of cheese grade sintered metal, which broke when I hit it with a hard rubber mallet (part of the flange broke off). I attempted to heat the pulley with a torch to remove it, but I'm afraid because the shaft is so small/short, I'll get the rest of the motor too hot and damage it. The motor is much noisier than I expected too, though I didn't run it until after I attempted to remove the pulley, so I can't be sure if that's because I damaged the bearings. All in all, $59 + tax wasted.
Scritto da: MRB1953
Good little motor
Good little motor. Operates smooth. Appears to be well made. Would be nice to have had some better documentation for it.
Scritto da: paul
Does the job
I am using it for a Ians BFF Shaker in a flight simulator so far so good. See how long it lasts
Scritto da: Michael Pare
Misleading Photo
I should have heeded the warning from another review that showed the one-sided pulley. AND in addition to that flaw it was also cracked upon arrival! I can't imagine what use-case a one-sided pulley would serve. For double the price of the motor without the pulley, this is bad. It cost me time and extra parts to get this going.
Scritto da: Enrique I
My pulley doesn't have one end.
The motor is ok, but the reason I put 3 stars is that the pulley in the ilustration and the pulley of the motor I received, are not the same. My pulley doesn't have one end. I attach some photos, so you can check the two pulleys are slightly different. Regards.
Scritto da: Donald Rogers
This is the best motor for the job.
I didn't dislike any part of it.
Scritto da: James Klingbile
works
Prompt delivery, item was as advertised

Povezani proizvodi

Otkrijte našu međunarodnu mrežu

Šaljemo u 28 zemalja, preko 200.000 proizvoda. Budite u toku, pretplatite se na newsletter.

Array