MAGBIT 786.18.0616 MAG786 3/8-inča sa 18-inčnim zvonastim svrdlom od visokougljičnog čelika

Name: MAGBIT 786.18.0616 MAG786 3/8-inča sa 18-inčnim zvonastim svrdlom od visokougljičnog čelika
Brand: MAGBIT
SKU: 0722170786071
Price: 47.94 EUR
Availability: InStock

Brand:MAGBIT

3.3/5

€
47.94

OPIS PROIZVODA SVRDLO ZA ZVONO ZA ČELIK SA VISOKOM UGLJENICOM OD PROIZVOĐAČA MAGBIT 786.18.0616 MAG786 Svrdlo za zvono za zvono od 3/8 inča od 18 inča s visokim sadržajem ugljika

Iznos

Dodaj u košaricu Kupi sada

EAN: 0722170786071

Kategorije Električni i ručni alati, Dijelovi i pribor za električne alate, Dijelovi i pribor za bušilice, Twist Bits, Svrdla, Jobber svrdla,

Otvor za riblje oko nalazi se blizu vrha žljebova za pomoć pri izvlačenju žice. Otvor za riblje oko nalazi se blizu vrha žljebova za pomoć pri izvlačenju žice. 2 udubljenja predviđena za postavljanje produžnih vijaka - bitovi od 5/8 inča i više. Točka od 82 stupnja za brže pokretanje.

Brand	‎MAGBIT
Customer Reviews	4.4 4.4 out of 5 stars 14 ratings 4.4 out of 5 stars
Cutting Angle String	82 Degrees
Cutting Angle String	‎82 Degrees
Cutting Diameter	none Inches
Cutting Diameter	‎none Inches
Finish	‎Nickel
Finish Type	Nickel
Finish Type	‎Nickel
Item model number	‎786.18.0616
Item Package Quantity	‎1
Item Weight	‎8.8 ounces
Manufacturer	‎Magnus Industries Inc.
Material	Alloy Steel
Material	‎Alloy Steel
Measurement System	‎Inch
Number of Flutes	‎2
Package Dimensions	‎18.9 x 0.8 x 0.8 inches
Part Number	‎786.18.0616
Shank Type	round shank
Shank Type	‎round shank
Surface Recommendation	‎Wood
Tool Flute Type	‎Spiral
Warranty Description	‎Return defective products to place of purchase for exchange or credit. Warranty does not apply to damage caused by abuse, misuse or alteration.

5 Star

4 Star

3 Star

2 Star

1 Star

Napišite svoju recenziju

Vaš email neće biti objavljen. Sva obavezna polja označena su s^*

Vaša ocjena

Scritto da: Frank H.

????

????

Scritto da: Schatz Family

good bit

works as advertised

Scritto da: Dan S.

Works Well

I needed a long bit to drill through 16 inches of junk/found lumber glued together in a "butcher-block" configuration, to drive a 3/8-inch dowel through for strength. This bit worked well and I'm quite satisfied with the results, though there are a couple of minor caveats. First, the spiral portion of the bit that contains the flutes and lands is quite short and I had to retract the bit several times per hole to clear out the drilling debris. I'm not subtracting points for this because I'd have had to clear the chips even if the bit's flutes/lands were full length, though perhaps not quite so often. Second, the lip relief was longer than I expected and that may have affected the drilling speed. On the other hand, it may have reduced seizing when drilling through hardened areas such as knots. Again, I'm not subtracting points because, all in all, the bit worked well.