Kontrola količine zraka serije Penn F93 za duboke bunare, otvara se pri padu tlaka, nema slavine, nema ventila za otpuštanje tlaka F93A-1C

Brand:Johnson Controls

3.7/5

134.12

Kontrole količine zraka serije F93 za duboke bunare kontroliraju količinu zraka u stambenim spremnicima za vodu u sustavima dubokih bunara. Duboki bunari duboki su više od 25 stopa (7,6 m). Kontrole serije F93 automatski održavaju volumen zraka u spremnicima za pohranjivanje vodenih sustava dubokih bunara dopuštajući zraku da izađe iz spremnika u okolnu prostoriju kada razina vode u spremniku padne (povećanje volumena zraka). Kontrole dubokog bunara F93 otvaraju zračni ventil pri padu razine vode u spremniku, ispuštaju višak zraka iz spremnika pri tlakovima do 100 psig (690 kPa). F93H ima ventil za otpuštanje minimalnog tlaka kako bi se izbjegao pad tlaka u spremniku ispod 25 psig (172 kPa). Koristite ovaj model na primjenama gdje se voda može brzo ispustiti. Za važne informacije o primjeni proizvoda pogledajte F93 serije kontrola volumena zraka za duboke bunare (Br. dijela 24-7664-3000).

čvrsto Noryl (termoplastika visokih performansi) tijelo otporno je na mehanička oštećenja i koroziju.
Country of Origin USA
Item model number F93A-1C
Manufacturer Johnson Controls, Inc
Package Dimensions 10.2 x 3.94 x 1.73 inches; 7.05 Ounces

3.7

8 Review
5 Star
79
4 Star
12
3 Star
4
2 Star
2
1 Star
3

Napišite svoju recenziju

Vaš email neće biti objavljen. Sva obavezna polja označena su s*

Scritto da: JS
Water tank switch
Fit great no issues
Scritto da: Beaty Wade Tharp
Fine valve
This style of valve is just fine for its function. My only wish is some ingenious engineer would figure out a way for the air vent portion of the valve to not get plugged up. I.e. some sort of wiper assembly that cleans off the air vent port as the float cycles up/down.
Scritto da: JERED ECKLE
Works like a champ!
Replaced one just like it in style. Immediately started working like it should after a few drain & fills of the tank!
Scritto da: MnBoy
It works.
Turned power off to deep well. Drained the water from the existing metal water tank through faucets. Waited until all the water... then air... left the tank. Closed the faucets. Took the old volume control out and put the new one in. This was a fairly easy procedure. Turned power on and waited for tank to fill. I could hear the air escaping the valve, which I did not hear on the old valve. The tank filled properly and I turned the faucets on to bleed air from lines. Pump runs only a fraction of what it did prior to new valve installation. I think the price is a bit high, but if it helps the pump by running less it is probably worth it.
Scritto da: Patrick
Identical to original.
Works fine but the arms on these floats are not a solid rod and that is what went bad on my old one. The arm bend up . These look identical to my original so i decided to beef up the rod with a piece of 8 awg solid copper wire soldered to the float arm. If not for the weak float arm this device would probably never fail.
Scritto da: Quail Valley Farm
Can't go wrong with Johnson Controls components
This switch closes the air pressure relief valve when the water level in the tank reaches the appropriate level. The switch was failing and dripping water in the pump house, non-stop. This is the exact same brand/model I replaced, and the one that failed was on the tank when I purchased the property in 2003, demonstrating its longevity. Given this is a farm tank, serving a home with a pool, and the property, it gets a significant workout. I suspect that because the well is inside of a structure, this switch and other components last somewhat longer than they would if the well system was exposed to the elements.
Scritto da: Mark Williamson
Says Penn, not Johnson controls.
Using it as a spare, not installed yet.
Scritto da: Roark
Works very well and has “secret” ability. :)
Perfect replacement for my deep-well system. Something not mentioned in the description is this has an *optional* outlet for gauge/pressure switch that is pre-threaded. If you dont need this feature, simply do nothing. This threaded recess does NOT by default connect to the tank-side pressure. If you want this feature, simply drill a small (tiny is fine!) hole in the threaded recess and screw your gauge or pressure switch in. That little hole connects the gauge to the pressure side of things. This means one unit can fill the role of two. Simply drill the hole to allow connection of a pressure switch or gauge. Neat!

Povezani proizvodi

hot
Emerson 90-342 Preklopni relej, 208/240V
2.2/5

€ 45.97

Emerson 90-342 Preklopni relej, 208/240V
2.2/5

€ 45.97

Otkrijte našu međunarodnu mrežu

Šaljemo u 28 zemalja, preko 200.000 proizvoda. Budite u toku, pretplatite se na newsletter.

Array